A dead outlet or a breaker that keeps tripping is easy to ignore for a day or two. Then the dryer stops working, or a ceiling light flickers every time the refrigerator kicks on, and the call gets made. That moment is where Greenlight Electric comes in. We handle electrical repair and installation for homes and properties throughout Sellersburg, and we are available every day from 5:30 AM to 8:30 PM. Call (502) 826-9879 for a quote.
Sellersburg is a town with a real mix of housing, from older homes on original wiring to newer construction that still needs circuits added, fans installed, or panels sized up for modern demand. We work across all of it. Whether you own the property, rent it out, or manage it for someone else, we handle the electrical side from the first call through the finished job.
The cost of electrical work depends on what the job actually involves. A single outlet replacement is a different scope from running a new circuit or replacing a panel, and the price reflects that difference. When you call, we ask about the situation, explain what the visit covers, and give you the rate before anything is scheduled. You know what the job costs and what it includes before we send anyone out.
What can change a quote is usually discovered once the work area is open. Wiring that differs from what was expected, a panel that needs capacity added before a new circuit can be run, or a permit and inspection requirement for certain work are the most common reasons a scope changes. When that happens, we walk you through it and get your agreement before proceeding. Nothing is added to the bill without a conversation first. The service page carries the full breakdown of what different job types typically involve.
A panel-level surge protector catches voltage spikes before they reach any circuit in the house. That matters in this region, where severe thunderstorms and grid-switching events happen often enough to damage appliances and electronics on a single event. A point-of-use strip protects only what is plugged into it. A whole-home device installed at the panel covers everything, including hardwired appliances and equipment that no strip can reach. It is a single installation with broad coverage.
Heavy shop equipment draws more current than a standard household circuit can safely carry. A welder, an air compressor, or a large table saw needs a dedicated circuit sized for its actual load, wired from the panel with the right breaker and the right outlet. We run these circuits correctly so the equipment operates without nuisance tripping and without stressing the wiring behind the wall. If the panel does not have the capacity, we assess what it takes to add it.
Older homes in this area sometimes still have knob-and-tube wiring in the walls, the attic, or the basement. It was the standard of its time, but it was not designed for the loads a modern home puts on a circuit, and it creates real concerns around insulation contact and added connections made over the decades. We handle full replacement and targeted remediation, bringing the affected circuits up to current code. This kind of work affects both safety and insurability, and it is worth addressing rather than working around.
A well pump runs on a dedicated circuit, and that circuit needs to be sized correctly for the pump's draw and wired in a way that holds up to the demands of continuous use. Irrigation systems have their own requirements depending on the size and layout of the system. We handle the electrical side of both: running the circuit, installing the right disconnect and protection, and confirming the installation is grounded and bonded properly before we leave.
Fault-finding calls start with a symptom: a circuit that goes dead, a breaker that trips under a normal load, an outlet that stopped working after a storm. The situation that leads to this call is usually something that has been building for a while. We trace the problem to its source rather than treating the symptom, and we check the surrounding wiring for arc-fault and ground-fault protection while we are there, because older circuits often lack it. We'll find the fault and fix it right.
The situation that leads to a panel upgrade is almost always the same. The home is running more than it was designed for, and the panel is showing it. Breakers trip under loads that should not trip them. There are no open slots for circuits that need to be added. The service size made sense when the house was built but does not match what the house is doing now. We run a load calculation, assess the service entrance, and replace the panel with one sized for actual demand. If the home needs a subpanel for a detached garage or a finished basement, that work ties into the same project.
Installation calls come from a specific need: a new appliance that requires a dedicated circuit, a room that needs outlets added, a fan going into a space that has never had one, an EV charger going into the garage. Each situation is different in what it requires from the panel and from the wiring path. We confirm panel capacity first, then run the circuit and make the connection. Code-compliant wiring throughout, permitted where the work requires it. Reach out and we'll start at the panel.
Crawl spaces, attics, and tall ceilings change how a job is planned, not whether it can be done. A home with a low crawl space and original wiring runs a different kind of job than a two-story house with a vaulted great room. The wiring path, the access points, and the time required all shift depending on what is between the panel and the destination.
Before any installation that involves running wire through a finished wall or an awkward space, we talk through the approach. That includes where we expect to open the wall, how we plan to route the cable, and what the finished result looks like. An electrical safety inspection on a home with limited access takes longer and covers different ground than one on a straightforward ranch layout. We account for that in the scope before the work starts, not after.
Local accountability means you always know who to call.
the panel and wiring page covers what the work involves before you call.
Same-day service is often available for repair calls, and we are reachable every day from 5:30 AM to 8:30 PM. When something stops working and it cannot wait, call (502) 826-9879 and describe what you are seeing. We ask a few questions, confirm what the visit involves, and get someone scheduled.
For tenants and businesses that need to stay operational during the work, we plan around it. That means confirming what circuits will be off and for how long before anything is shut down, and sequencing the work to minimize disruption where the layout allows. A rental property with occupied units gets the same attention to planning as a home where the owner is present. Getting your electrical problem handled starts with a quick call.
We serve Sellersburg and extend coverage throughout Clark County and the surrounding communities. Clarksville, Jeffersonville, Charlestown, Memphis, and New Albany are all areas we cover regularly. Whether the job is in town or in the surrounding county, the process is the same: a call, a quote, and a licensed electrician on-site ready to work.
The more specific you can be, the faster we can scope the job. It helps to know which room or area is affected, whether the problem is constant or comes and goes, whether a breaker has tripped, and roughly how old the panel and wiring are. If there is a smell, a sound, or visible discoloration near an outlet or fixture, mention that too.
On most multi-day jobs, restoring power at the end of each day is part of how we stage the work. We confirm the plan with you before the job starts so the property is not left without power overnight unless the scope genuinely requires it.
Report it right away. A fault that comes and goes is often harder to diagnose once it becomes permanent, because the conditions that trigger it are no longer present. Catching it while it is still intermittent gives us more to work with and reduces the chance that a small problem becomes a larger one.
Running power to a detached garage involves a dedicated circuit from the main panel, with the cable either buried underground or run through conduit depending on the route and local requirements. We assess the distance, the intended load, and the panel capacity before we scope the job. If the garage needs its own subpanel to support multiple circuits, we handle that as part of the same project.
Permitted work produces an inspection record once the inspection is passed, which is the documentation most insurers and property managers are looking for. For work that does not require a permit, we can describe what was done and what was installed. If you have a specific documentation requirement, mention it when you call and we will confirm what we can provide.
New circuits for an addition are run from the main panel or a subpanel if the main panel does not have capacity. We assess the existing service first to confirm it can carry the additional load. If the service needs to be upgraded to support the addition, we handle that as part of the same project rather than treating it as a separate job later.
A well pump runs on a dedicated circuit that has to be sized for the pump's draw, and the disconnect and protection equipment at the pump needs to meet current code. If you are adding a circuit, replacing a pump, or have had issues with the pump tripping its breaker, that is electrical work we handle. Call and describe the situation and we will explain what the visit involves before anything is scheduled.
We want to know about it. If the same fault returns, call us and describe what is happening. We assess whether the original repair addressed the root cause or whether something else is contributing to the problem. A fault that returns after a repair is taken seriously, not treated as a routine callback.
Yes. When we work on a panel, we confirm that every breaker is correctly labeled before we leave. If the existing labels are missing or inaccurate, we update them as part of the job. A panel that is properly labeled makes every future service call faster and safer.
Older homes in this area often have wiring systems, panel types, and protection devices that were standard when the house was built but do not meet current requirements. An inspection on an older home covers the panel condition, the wiring type, grounding and bonding, and whether arc-fault and ground-fault protection is in place where it is now required. The findings give you a clear picture of what the system actually needs rather than what it used to need.
Greenlight Electric covers Sellersburg and the towns around it, from Clarksville and Jeffersonville to Charlestown and New Albany. If the problem is in Clark County, we handle it. Call (502) 826-9879 for a quote and get a price before anything is scheduled. We are available every day from 5:30 AM to 8:30 PM. We test every circuit. We label every breaker. We leave it safe.
Check our full service area. Close by, we also work in: Clarksville, Jeffersonville, Charlestown, New Albany, St. Matthews.
Below is a plain-language look at the electrical work we handle in Sellersburg and Clark County. Each row covers what a service includes, who it fits best, and one practical thing worth knowing before you call. If you have questions about a specific job, the fastest way to get a real answer is to call us directly.
| Service | Scope of Work | Common Situations | Things to Know |
|---|---|---|---|
| Dedicated Appliance Circuits | Electric dryer and range circuitsRefrigerator and washer circuitsWorkshop and garage circuitsCorrect breaker sizing and outlet type | Homeowners adding a major appliance or setting up a garage workshop | Running a large appliance on a shared circuit is a common cause of nuisance tripping and can shorten appliance life. A dedicated circuit is the code-required solution. |
| Electrical Repairs & Troubleshooting | Dead outlets and switchesFlickering or dimming lightsBurning smells near panels or receptaclesCircuit tracing and fault diagnosis | Homeowners and property managers dealing with an active electrical problem | We trace faults to the source rather than resetting breakers and leaving. A repair visit often turns up related issues worth addressing at the same time. |
| Whole-Home Surge Protection | Panel-level surge device installationCorrect bonding and groundingFull-house coverageWorks alongside point-of-use strips | Homeowners with sensitive electronics or frequent storm activity in the area | Clark County's summer thunderstorm season and grid-switching events make panel-level surge protection a practical choice. One device covers every circuit in the house, including hardwired appliances. |
| EV Charger Installation | 240-volt dedicated circuitPanel capacity assessmentOutlet or hardwired connectionGarage and parking area runs | EV owners who want faster charging than a standard household outlet provides | If the panel does not have capacity for the new circuit, we handle the panel upgrade as part of the same project so everything is done in one visit. |
| Lighting Installation | Recessed and LED can lightsExterior security and flood lightsVanity and pendant fixturesMotion sensor and driveway lighting | Homeowners updating interior lighting or adding outdoor security fixtures | Outdoor fixtures in Kentucky's climate need weatherproof enclosures and proper grounding. We confirm both before the job is done. |
| Ceiling Fan Installation | Fan-rated box installationNew wiring where none existsReplacement fan hookupRemote and wall-control wiring | Rooms without a ceiling fan or with an existing fixture that needs replacing | Many older Sellersburg homes have ceiling boxes that are not rated for a fan's weight and movement. We replace the box as part of the installation when needed. |
| Basement & Sump-Pump Circuits | Dedicated sump-pump circuitBasement outlet installationGFCI protection in unfinished areasBackup power circuit options | Homeowners finishing a basement or protecting against flooding with a reliable sump circuit | Sump pumps should run on a dedicated circuit with GFCI protection. A shared circuit can trip at the wrong moment. We size and wire the circuit so the pump has reliable power when it needs it. |
| Outlet & Switch Installation | Standard and USB outletsGFCI and AFCI outletsWeatherproof outdoor receptaclesDimmer and switch replacement | Homeowners adding outlets, upgrading receptacles, or replacing worn switches | Tamper-resistant outlets are required in new construction and recommended in any home with children. We install the right outlet type for the location and the code requirement. |
| Wiring & Rewiring | Full home rewiringKnob-and-tube replacementAluminum wiring remediationPartial rewiring for additions | Older homes with outdated wiring systems that affect safety or insurability | Aluminum wiring and knob-and-tube systems are common in Sellersburg's older housing stock. Addressing them improves safety and can resolve issues flagged during a home sale or insurance review. |
| Electrical Panel & Service Upgrades | 100-amp to 200-amp service upgradeFull panel replacementLoad calculation before sizingMeter socket and service entrance work | Homes running central air, electric appliances, and modern loads on an undersized service | A panel upgrade is permitted and inspected work. We handle the permit coordination and confirm the installation meets current code before the job is closed out. |
| Older-Home Rewiring | Full system assessmentKnob-and-tube and aluminum wiring replacementGrounding upgradesCode-violation corrections | Sellersburg homeowners with pre-1970s wiring that has never been updated | Older wiring systems were not designed for the loads a modern home puts on them. Rewiring addresses safety, brings the home up to current code, and can resolve issues flagged by insurers. |
| Backup Generator Installation | Transfer switch installationGenerator hookup and wiringCritical circuit identificationCode-compliant disconnect | Homeowners in Clark County who need power during storm outages | A transfer switch is required by code and protects utility workers by isolating your home from the grid before the generator comes on. We handle the electrical side. We do not sell or service the generator unit itself. |
| Electrical Safety Inspections | Panel and wiring condition reviewGrounding and bonding checkGFCI and AFCI protection auditWritten findings and recommendations | Buyers, landlords, and homeowners who have not had the system reviewed in years | An inspection before a property sale or rental can surface issues early, when they are easier and less expensive to address than after a transaction is underway. |
| Wiring for Additions & Remodels | Rough-in wiring for new roomsBathroom and kitchen circuitsBasement and attic wiringFinal connections and cover plates | Homeowners finishing a basement, adding a bathroom, or building out a garage | Addition wiring is permitted work in most jurisdictions. We coordinate the permit and schedule the inspection so the work is documented and code-compliant before the walls close. |
| Breaker & Fuse Repair | Breaker replacementFuse panel assessmentTripping breaker diagnosisPanel interior inspection | Homes where a breaker trips repeatedly or will not hold after being reset | A breaker that trips under normal load, feels hot, or smells like burning plastic is a sign the breaker or the wiring behind it needs attention, not just a reset. |
Call us at (502) 826-9879 to get a price on any of the services above and find out when we can get someone out to your Sellersburg property.
(502) 826-9879