When a tenant reports a dead outlet or a builder needs circuits roughed in before the drywall goes up, the call lands with us. Greenlight Electric handles electrical work across New Albany for the people who need it handled correctly and on a schedule that works for them. That includes landlords dealing with a rental that has flagged a code issue, property managers coordinating work across multiple units, and homeowners who have put off a panel concern long enough. We cover the full range of residential and commercial electrical work, and same-day service is often available when something will not keep.
New Albany's housing stock runs toward older construction, and older construction brings its own set of electrical realities. Panels that were sized for a different era, wiring that has never been updated, circuits added over the years without documentation. We work through all of it. Work is performed by licensed electricians who assess what is actually there before recommending anything. Call (502) 826-9879 for a quote.
Not every electrical problem in a home or building originates inside it. When power is out on one side of the panel, or when a circuit behaves differently from everything else, the fault may sit at the meter, the service entrance, or on the utility's own lines. Part of a diagnostic visit is working out exactly where the problem starts.
If the fault turns out to be on the utility's side, we tell you that clearly and explain what the next step looks like. That usually means contacting the utility company directly and describing what was found. We do not leave a customer guessing. If the problem is on our side of the meter, we trace it, explain what it involves to fix it, and give you a price before any work begins.
Electrical work is priced by what the job actually involves. A single outlet replacement is a different scope from a panel upgrade, and a panel upgrade is a different scope from rewiring a floor of a building. The price is confirmed on the call, before anything is scheduled, and it covers what we have discussed.
A few things can shift a quote once the work area is opened up. Wiring conditions inside the wall, panel capacity that needs addressing before a new circuit can be added, or permit and inspection requirements that apply to the specific job are the most common ones. When something changes, we explain it before we proceed. Nothing is added to the bill without your knowledge.
To get a number, call and describe what you are dealing with. You get the rate on the phone and a clear explanation of what it covers. Call us and the rest is handled.
New Albany is a city with a real mix of property types, and what a visit involves depends heavily on what is there. A house built several decades ago presents differently from a newer build, and a commercial space presents differently from either. The service page carries the full breakdown of what we handle. Below is how the work tends to divide across the kinds of calls we take here.
Most calls start with something the customer has noticed: a breaker that trips under a normal load, an outlet that stopped working, lights that flicker or dim when a large appliance turns on. The situation that leads to this call is usually one of those small signals that something in the circuit or the wiring is not right. We trace the fault to its source rather than addressing only the symptom. Honest recommendations on repairs, never an upsell. If a repair is the right call, that is what we recommend.
The situation that leads to a panel call is usually a home or building that has outgrown its original electrical capacity. Panels sized for older demand struggle when central cooling, electric appliances, and EV chargers are all drawing from the same service. We run a load calculation before recommending a specific upgrade so the new panel is sized for what the property actually needs, including any circuits that are planned for the future. This work is permitted and inspected. We handle that process as part of the job.
New circuits, new fixtures, new appliances that need dedicated power. These are the calls that come in when a property is being updated or when something new is being added that the existing wiring was not designed to support. We handle the electrical side from the panel out, code-compliant wiring throughout, and we confirm at the end that everything is functioning correctly. We test every circuit. We label every breaker. We leave it safe.
Where the panel sits and how it is accessed shapes how a visit goes. In a lot of New Albany's older homes, the panel is in the basement or in a utility area that may not have been touched in years. Knowing that before we arrive means we can plan the visit correctly.
A few things make a service call go smoothly. Clear access to the panel and to the areas where work is happening saves time. If the panel is in a finished basement or behind stored items, clearing a path before we arrive is worth doing. For rental properties, having the tenant available or having access arranged ahead of time avoids delays on both sides.
Local accountability means you always know who to call. When something comes up after the visit, reaching someone who knows the job is straightforward.
For a fuller picture of the job, see the page about wiring and panels.
Battery-only detectors are easy to ignore. Hardwired alarms with battery backup are a different level of protection, and in many rental properties they are a code requirement. We install hardwired smoke and carbon monoxide detectors, wire them together so they communicate across the home, and confirm they are functioning before we leave.
Replacing a fixture is straightforward when the existing wiring is in good shape. In older homes, it sometimes is not. We check the box, the wiring, and the circuit before the new fixture goes up. Ceiling fan installation follows the same process. A box that is not rated for a fan's weight and movement needs to be replaced before the fan is hung. We handle that as part of the installation.
Aluminum branch circuit wiring was common in homes built during a particular stretch of decades, and New Albany has its share of those properties. The concern is not the aluminum itself but the connections, which can loosen over time and create heat and arcing at outlets and switches. Remediation means addressing those connections correctly, either through approved connectors or by replacing the affected devices with aluminum-rated components. This affects insurability as well as safety, and it is work worth doing properly.
A panel-level surge protector intercepts voltage spikes before they reach any circuit in the home. In a region where severe thunderstorms and grid-switching events are part of the seasonal pattern, that kind of protection covers things that a power strip never reaches: hardwired appliances, the HVAC circuit, the panel itself. Installation is a clean, defined job. We install the device, bond it correctly, and confirm it is working before we leave.
A new appliance that draws significant power needs its own dedicated circuit. A hot tub needs a dedicated circuit, a disconnect, and GFCI protection at the equipment. Workshop tools and compressors have similar requirements. In each case, we assess panel capacity first, confirm there is room for the new circuit, and run the wiring to where it is needed. If the panel needs capacity added first, that conversation happens before the circuit work is priced.
Getting your electrical problem handled starts with a quick call. Same-day service is often available for repair calls and urgent situations. We are open every day from 5:30 AM to 8:30 PM, and calling early gives the best chance of getting someone out the same day.
For tenants in an occupied rental, we work around what is there. For businesses that need to stay open during a repair, we plan the visit accordingly. We confirm the appointment window when you call and let you know what to have ready. There is no complicated process on your end.
If the situation involves a sparking outlet, a burning smell near the panel, or anything that suggests an immediate safety concern, do not wait. Call (502) 826-9879 and describe what you are seeing. We will tell you what to do while we work out the visit.
We serve New Albany as a primary area and take calls throughout Floyd County and the surrounding communities. Clarksville, Jeffersonville, Sellersburg, Floyds Knobs, and Galena are all covered. Whether the property is a single-family home, a rental unit, a commercial space, or something in between, the work is handled on-site by licensed electricians who know the area.
There is no difference in how a call is handled based on where in the county it comes from. Call, describe the situation, and we will confirm the scope and the price before anything is scheduled.
Call and describe what the tenant reported. We ask a few questions to understand the situation, give you a price on the phone, and schedule the visit around what works for the tenant and the property. If the issue is something that needs attention the same day, same-day service is often available. Documentation of what was found and what was done is part of how we handle rental property work.
Permit requirements depend on the type of work and sometimes on whether the property is inside city limits or in the unincorporated county. Panel upgrades, new circuits, and certain installation work typically require a permit and a final inspection. We handle that process as part of the job and confirm what applies to your address before we schedule. It does not change how you call or how the quote works.
An electric gate needs a dedicated circuit run to the gate location, along with weatherproof wiring and connections that can handle outdoor conditions. The supply needs to be sized for the gate motor and any additional features like intercoms or lighting. We handle the electrical supply side and confirm the installation meets the requirements of the gate equipment before we leave.
Running power to a detached garage involves a dedicated circuit from the main panel, with the cable either buried underground or run through conduit depending on the route and local requirements. We assess the distance, the intended load, and the panel capacity before we scope the job. If the garage needs its own subpanel to support multiple circuits, we handle that as part of the same project.
Before we consider the job complete, we test the circuits, confirm the panel is labeled, and check that every outlet, switch, and fixture is functioning as it should. If anything is not right, we address it before we leave. We test every circuit. We label every breaker. We leave it safe.
We will tell you what we found and explain what falls outside our scope. Utility-side issues, such as a problem with the service drop or the meter, need to be reported to the utility company directly. We can help you identify what the issue is and point you toward the right contact.
Yes. When you call, we ask questions about what you are dealing with and give you a clear description of what the visit is likely to involve along with the price. You have everything you need to decide before anything is scheduled. Call (502) 826-9879 and we will walk through it with you.
Yes. An electrical audit or inspection can produce a clear circuit map that shows what each breaker controls and where the circuits run. This is useful for older properties where the original wiring layout is unknown, for landlords managing multiple units, and for anyone who wants a complete picture of their electrical system before selling or renovating.
Yes. We assess what has been done, confirm whether it meets current standards, and take the job from that point forward. If the prior work has problems that need to be corrected before we can continue, we explain what those are and what it takes to address them before we proceed.
A full rewire is typically done one area at a time, with power maintained to the rest of the property while each section is worked on. We discuss the staging plan before we start so you know which areas will be affected and when. The goal is to keep the disruption manageable and restore power to each completed section before moving to the next.
Greenlight Electric handles electrical repair and installation across New Albany and Floyd County, seven days a week from 5:30 AM to 8:30 PM. Describing what you are seeing is enough to get started. We ask the questions, work out what the visit involves, and give you a price before we schedule anything.
Ready for your wiring. Call today. (502) 826-9879
Check our full service area. Close by, we also work in: Clarksville, Sellersburg, Jeffersonville, St. Matthews, Charlestown.
Below is a plain-language look at the electrical work we handle in New Albany and Floyd County. Each row covers what a service includes, who it fits best, and one practical thing worth knowing before you call. If you have questions about a specific job, the fastest way to get a real answer is to call us directly.
| Service | Scope of Work | Common Situations | Things to Know |
|---|---|---|---|
| Dedicated Appliance Circuits | Electric dryer and range circuitsRefrigerator and washer circuitsWorkshop and garage circuitsCorrect breaker sizing and outlet type | Homeowners adding a major appliance or setting up a garage workshop | Running a large appliance on a shared circuit is a common cause of nuisance tripping and can shorten appliance life. A dedicated circuit is the code-required solution. |
| Electrical Repairs & Troubleshooting | Dead outlets and switchesFlickering or dimming lightsBurning smells near panels or receptaclesCircuit tracing and fault diagnosis | Homeowners and property managers dealing with an active electrical problem | We trace faults to the source rather than resetting breakers and leaving. A repair visit often turns up related issues worth addressing at the same time. |
| Whole-Home Surge Protection | Panel-level surge device installationCorrect bonding and groundingFull-house coverageWorks alongside point-of-use strips | Homeowners with sensitive electronics or frequent storm activity in the area | Floyd County's summer thunderstorm season and grid-switching events make panel-level surge protection a practical choice. One device covers every circuit in the house, including hardwired appliances. |
| EV Charger Installation | 240-volt dedicated circuitPanel capacity assessmentOutlet or hardwired connectionGarage and parking area runs | EV owners who want faster charging than a standard household outlet provides | If the panel does not have capacity for the new circuit, we handle the panel upgrade as part of the same project so everything is done in one visit. |
| Lighting Installation | Recessed and LED can lightsExterior security and flood lightsVanity and pendant fixturesMotion sensor and driveway lighting | Homeowners updating interior lighting or adding outdoor security fixtures | Outdoor fixtures in Kentucky's climate need weatherproof enclosures and proper grounding. We confirm both before the job is done. |
| Ceiling Fan Installation | Fan-rated box installationNew wiring where none existsReplacement fan hookupRemote and wall-control wiring | Rooms without a ceiling fan or with an existing fixture that needs replacing | Many older New Albany homes have ceiling boxes that are not rated for a fan's weight and movement. We replace the box as part of the installation when needed. |
| Basement & Sump-Pump Circuits | Dedicated sump-pump circuitBasement outlet installationGFCI protection in unfinished areasBackup power circuit options | Homeowners finishing a basement or protecting against flooding with a reliable sump circuit | Sump pumps should run on a dedicated circuit with GFCI protection. A shared circuit can trip at the wrong moment. We size and wire the circuit so the pump has reliable power when it needs it. |
| Outlet & Switch Installation | Standard and USB outletsGFCI and AFCI outletsWeatherproof outdoor receptaclesDimmer and switch replacement | Homeowners adding outlets, upgrading receptacles, or replacing worn switches | Tamper-resistant outlets are required in new construction and recommended in any home with children. We install the right outlet type for the location and the code requirement. |
| Wiring & Rewiring | Full home rewiringKnob-and-tube replacementAluminum wiring remediationPartial rewiring for additions | Older homes with outdated wiring systems that affect safety or insurability | Aluminum wiring and knob-and-tube systems are common in New Albany's older housing stock. Addressing them improves safety and can resolve issues flagged during a home sale or insurance review. |
| Electrical Panel & Service Upgrades | 100-amp to 200-amp service upgradeFull panel replacementLoad calculation before sizingMeter socket and service entrance work | Homes running central air, electric appliances, and modern loads on an undersized service | A panel upgrade is permitted and inspected work. We handle the permit coordination and confirm the installation meets current code before the job is closed out. |
| Older-Home Rewiring | Full system assessmentKnob-and-tube and aluminum wiring replacementGrounding upgradesCode-violation corrections | New Albany homeowners with pre-1970s wiring that has never been updated | Older wiring systems were not designed for the loads a modern home puts on them. Rewiring addresses safety, brings the home up to current code, and can resolve issues flagged by insurers. |
| Backup Generator Installation | Transfer switch installationGenerator hookup and wiringCritical circuit identificationCode-compliant disconnect | Homeowners in Floyd County who need power during storm outages | A transfer switch is required by code and protects utility workers by isolating your home from the grid before the generator comes on. We handle the electrical side. We do not sell or service the generator unit itself. |
| Electrical Safety Inspections | Panel and wiring condition reviewGrounding and bonding checkGFCI and AFCI protection auditWritten findings and recommendations | Buyers, landlords, and homeowners who have not had the system reviewed in years | An inspection before a property sale or rental can surface issues early, when they are easier and less expensive to address than after a transaction is underway. |
| Wiring for Additions & Remodels | Rough-in wiring for new roomsBathroom and kitchen circuitsBasement and attic wiringFinal connections and cover plates | Homeowners finishing a basement, adding a bathroom, or building out a garage | Addition wiring is permitted work in most jurisdictions. We coordinate the permit and schedule the inspection so the work is documented and code-compliant before the walls close. |
| Breaker & Fuse Repair | Breaker replacementFuse panel assessmentTripping breaker diagnosisPanel interior inspection | Homes where a breaker trips repeatedly or will not hold after being reset | A breaker that trips under normal load, feels hot, or smells like burning plastic is a sign the breaker or the wiring behind it needs attention, not just a reset. |
Call us at (502) 826-9879 to get a price on any of the services above and find out when we can get someone out to your New Albany property.
(502) 826-9879